The Mass Metrology Seminar is a two-week, "hands-on" seminar. It incorporates approximately 30 percent lectures and 70 percent demonstrations and laboratory work in which the participant performs measurements by applying procedures and equations discussed in the classroom. The seminar focuses on the comprehension and application of the procedures, the equations, and calculations involved. The seminar includes the operation of the laboratory equipment, review of publications, standards, specifications, and tolerances relevant to the measurements. Training covers mass calibration procedures published in NISTIR 6969 and NISTIR 5672 and are suitable for the calibration of mass standards to OIML R111 Class E2 through M3 tolerances, ASTM classes 1 through 7 and NIST HB 105-1 Class F. Training is provided to enable the participant to correctly identify and implement the correct calibration process for each weight classification. Each procedure and the entire seminar incorporates concepts covered in the Fundamentals of Metrology seminar, especially, concepts related to metrological traceability, statistical analysis, measurement assurance methods, uncertainty analyses, software validation, and generation of ISO/IEC 17025 compliant calibration certificates for all measurements made during the seminar.
At the end of this seminar, using Standard Operating Procedures 1, 2, 4, 5, 7, 8, 9, 29, 30, and 34 and Good Measurement Practices 10, 11, 12, and 13 participants will be able to:
Note regarding course level and expectations: This course is conducted equivalent to a university level course and is part of our IACET accredited processes with requirements to demonstrate successful achievement of learning objectives within each module. Significant time outside of the classroom and laboratory is expected and is commonly reported (1 hour to 2 hours per day) to complete homework, reading, data entry, and creation and editing of calibration certificates. Students should avoid trying to meet other obligations while attending this course as much as possible.
Participants are encouraged to bring template versions of the mass calibration certificates issued by their laboratory as a starting point for the calibration certificates to be submitted during the seminar. Alternatively, participants should bring the calibration certificate they generated during the Fundamentals of Metrology seminar as a starting point. The former is recommended! Feedback and suggested changes to ensure ISO/IEC 17025 compliance will be provided during the seminar. Generation of calibration certificates will be required, so come prepared. A number of notebooks and course materials will be provided, so please ensure you have extra luggage space to carry these items.
Successful completion of the Fundamentals of Metrology Seminar is a prerequisite for the Mass Metrology Seminar. The Mass Metrology Seminar is built on the concepts learned during the Fundamentals of Metrology Seminar, applying units, measurement uncertainty, measurement assurance, traceability and Quality Management System concepts to the mass calibration procedures.
Please make sure you read the NIST Visitor and Contractor Protocols for Mitigating COVID-19 Exposure on NIST Campuses page before arriving on site. For more information please visit: www.nist.gov/campus-status
It is strongly recommended that you complete the Basic Mass Metrology CD as it will give you a head start on the Mass Seminar, including exposure to the contents of NISTIR 6969, Selected Laboratory and Measurement Practices, and NISTIR 5672, Advanced Mass Calibrations and Measurements Assurance Program for the State Calibration Laboratories.. Completing the CD should take 16 to 40 hours. Participants are encouraged to read and comprehend as much as possible the content of NISTIR 6969 and NISTIR 5672 regardless of completing NISTSP 1001. If you have problems downloading the material, please send Yvonne Branden (yvonne.branden [at] nist.gov) a request to mail a copy of the CD.
NOTE: additional reading pre-work and Excel preparation recommendations may be sent by the instructor prior to the seminar. Extensive use of Excel is made in this course; strong familiarity equation entry and validation is essential.
Laboratory Auditing Program (LAP) problems are assigned at the completion of the course to those metrologists who participate in the NIST OWM State Laboratory Program. Acceptable completion of the problems is required for NIST Office of Weights and Measures Laboratory Recognition in support of mass calibrations. (See Handbook 143, Program Handbook training requirements as updated here.
To receive a Training Certificate for this course, successful completion requires participants to actively participate in the entire course (e.g., 100 % attendance, take notes, engage in discussions, ask questions), complete all classroom, homework, and application exercise assignments, successfully perform mass calibrations as evidenced by measurement results entered in course control charts and calibration certificates, and pass a written final exam. In addition, students submit a series of calibration certificates that are graded based on SOP 1 and NIST SP 811 criteria, as evidence of completion of all application exercises conducted during the hands-on portion of class exercises.
*Homework note: students generally report taking one to two hours for homework each night.
This training seminar is open to State weights and measures regulatory officials and industry metrologists. Please make sure you read the NIST Visitor and Contractor Protocols for Mitigating COVID-19 Exposure on NIST Campuses page before arriving on site. For more information please visit: https://www.nist.gov/campus-status. This course is also available for non-weights and measures participants.
The current fee for this seminar is $5,600 and confirmed participants will be sent payment instructions. This registration fee does not cover travel, lodging or meal costs. Registration fees for State weights and measures regulatory officials and metrologists are funded by NIST OWM.
Elizabeth Koncki and Mark Ruefenacht
Email: elizabeth.koncki [at] nist.gov
NIST Office of Weights and Measures
You will need a government-issued photo ID (e.g., passport or driver's license) when you check into the Visitors Center at the entrance of NIST and if bringing a vehicle onto the NIST campus, a vehicle registration card.
PLEASE NOTE: Effective July 21, 2014, under the REAL ID Act of 2005 (https://www.dhs.gov/real-id/real-id-frequently-asked-questions), agencies, including NIST, can only accept a state-issued driver's license or identification card for access to federal facilities if issued by states that are REAL ID compliant or have an extension. NIST currently accepts other forms of federally issued identification in lieu of a state-issued driver's license, such as a valid passport, passport card, DOD's Common Access Card (CAC), Veterans ID, Federal Agency HSPD-12 IDs, Military Dependents ID, Transportation Workers Identification Credential (TWIC), and TSA Trusted Traveler ID. See Visitor Information for the latest information.