Skip to main content
U.S. flag

An official website of the United States government

Dot gov

The .gov means it’s official.
Federal government websites often end in .gov or .mil. Before sharing sensitive information, make sure you’re on a federal government site.

Https

The site is secure.
The https:// ensures that you are connecting to the official website and that any information you provide is encrypted and transmitted securely.

bullet under microscope
Credit: T.B. Renegar/NIST

Preserving the Kennedy Assassination Bullets in Digital Form

NIST researchers create high-resolution 3D models from these important historical artifacts.

Using the sophisticated digital measurement techniques of modern forensics, researchers at the National Institute of Standards and Technology (NIST) have created high-resolution 3D replicas of the bullets used to assassinate President John F. Kennedy.

Why do this, so many years after the tragic events of Nov. 22, 1963? The mission of the National Archives, the keeper of these historic artifacts, is to provide public access to federal government records, and it receives many requests each year for access to these artifacts. The digital replicas created by NIST will allow the National Archives to release the 3D models to the public so anyone can view them while the originals remain safely preserved in their temperature and humidity-controlled vault.

The National Archives will make the data available in its online catalog in early 2020, allowing the artifacts to be viewed virtually from any angle or position, revealing surface details down to the microscopic level.

For additional information, see the related article, “Kennedy Assassination Bullets Preserved in Digital Form.”

A copper bullet in a glass jar, sealed at the top.
Credit: J. Stoughton/NIST

This image shows the bullet that struck both President John F. Kennedy and Texas Gov. John Connally, carefully preserved inside its glass vial prior to scanning. Known as the “stretcher bullet,” it was found on Gov. Connally's stretcher after he was taken to the hospital. It was later designated as CE 399 by the Warren Commission.

 

Man looks into microscope while holding bullet below.
Credit: C. Suplee/NIST

NIST physical scientist Robert Thompson examines the stretcher bullet before the scanning process begins. He’s looking for any microscopic landmarks that could be used to guide the creation of the detailed topographical scans.

 

Man in lab coat leans over bullet in holder.
Credit: J. Stoughton/NIST

NIST physical scientist Thomas Brian Renegar prepares the stretcher bullet for a scanning run by mounting it in a custom-made non-marring chuck. Renegar designed the chuck and fabricated it using a 3D printer.

 

Person wearing green gloves positions bullet in holder.
Credit: J. Stoughton/NIST

The plastic and rubber coated chuck must hold the bullet tightly enough that it remains still during the scanning process, yet gently enough that it does not mar the bullet’s soft copper surface.

 

A device holds a sample under a microscope.
Credit: J. Stoughton/NIST

Prior to each scanning run, the system is calibrated using a known sample: NIST Standard Reference Material 2460, better known as the standard bullet.

 

Man in lab coat reaches under microscope to place sample.
Credit: J. Stoughton/NIST

Renegar mounts the bullet, held by the chuck, on the scanning bed of the microscope.

 

A man looks at the sample held under a microscope.
Credit: C. Suplee/NIST

Renegar examines the positioning of the bullet before the scanning run begins. Twenty-two such scanning runs were needed to fully capture all the surface details of the stretcher bullet from every angle, resulting in 1,699 individual measurements of the bullet’s surface.

 

The side of a man's face as he looks at a bullet model on a screen.
Credit: J. Stoughton/NIST

A NIST researcher views a preliminary 3D model stitched together from the many high-resolution images captured during the scanning process.

 

Person wearing green glove reaches under microscope to remove sample.
Credit: J. Stoughton/NIST

With the scanning run complete, the bullet is removed from the microscope and repositioned so it can be scanned at a new angle.

 

A man in a lab coat and green gloves places a bullet under a microscope.
Credit: J. Stoughton/NIST

NIST physical scientist Mike Stocker places the bullet, wrapped in a silicone sleeve, on the microscope for a new run.

 

Closeup of bullet in holder under microscope
Credit: J. Stoughton/NIST

During the scanning process, a bright light evenly illuminates the bullet while the microscope captures a series of images. In the end, the individual images were stitched together to create a seamless 3D model.

 

Bullet fragment is illuminated under microscope lens.
Credit: T.B. Renegar/NIST

In addition to the stretcher bullet, detailed scans and models were also made of five other artifacts, including two fragments from the bullet that fatally wounded President Kennedy. In this image, one of those fragments is illuminated beneath the microscope’s lens as it is scanned. Due to its complex geometry, more than 30 scans were required to image its entire surface.

Created December 5, 2019