Take a sneak peek at the new NIST.gov and let us know what you think!
(Please note: some content may not be complete on the beta site.).

View the beta site
NIST logo

Publications Portal

You searched on: Author: jack stone jr

Displaying records 21 to 30 of 57 records.
Resort by: Date / Title


21. Area Measurement of Knife Edge and Cylindrical Apertures using Ultra Low Force Contact Fiber Probe on a CMM
Published: 1/1/2008
Authors: Balasubramanian Muralikrishnan, Jack A Stone Jr., John Richard Stoup
Abstract: Several radiometric and photometric measurements depend on high accuracy area measurement of precision apertures. Some apertures have sharp edges and are generally measured optically. At the Precision Engineering Division (PED) of the National Instit ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=824632

22. Calibrating Laser Vacuum Wavelength With a GPS-Based Optical Frequency Comb
Published: 5/15/2007
Authors: Jack A Stone Jr., Liang Lu, Patrick F Egan
Abstract: The Global Positioning System (GPS) can deliver an exceptionally accurate frequency standard to any point in the world. When we use the GPS signal to control an optical frequency comb, the comb+GPS system provides laser light with well-known frequenc ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=823235

23. Roundness Measurements Using the NIST Fiber Probe
Published: 1/1/2007
Authors: Balasubramanian Muralikrishnan, Jack A Stone Jr., John Richard Stoup
Abstract: We have described a fiber probe for dimensional measurement of micro-holes in the 2004 and 2006 ASPE annual meetings. In this abstract, we describe the adaptation of this probe for measuring roundness of tiny holes and knife edge apertures. In its cu ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=823241

24. The NIST Advance Measurement Laboratory: At the Leading Edge of Measurement Science and Technology
Published: 9/20/2006
Authors: C Londono, John Russell Lawall, Michael T Postek, Jack A Stone Jr., John Richard Stoup
Abstract: The National Institute of Standards and Technology as the U.S. National Metrology Institute has the fundamental responsibility to continuously push the limits of measurement science (metrology) to promote U.S. innovation and industrial competitivenes ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=200115

25. The NIST Advanced Measurement Laboratory: at the Leading Edge of Measurement Science and Technology
Published: 8/1/2006
Authors: C Londono, John Russell Lawall, Michael T Postek, Jack A Stone Jr., John Richard Stoup
Abstract: The National Institute of Standards and Technology as the U.S. National Metrology Institute has the fundamental responsibility to continuously push the limits of measurement science (metrology) to promote U.S. innovation and industrial competitivenes ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=824616

26. Enhanced Capabilities of the NIST Fiber Probe for Microfeature Metrology
Published: 1/1/2006
Authors: Balasubramanian Muralikrishnan, Jack A Stone Jr., John Richard Stoup
Abstract: We have previously reported work in the area of fiber probe development at NIST for micro feature measurement. This probe, which we refer to as the Fiber Deflection Probe, functions by optically imaging the stem from two orthogonal directions a few m ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=823213

27. Fiber Deflection Probe Uncertainty Analysis for Micro Holes
Published: 1/1/2006
Authors: Balasubramanian Muralikrishnan, Jack A Stone Jr., John Richard Stoup
Abstract: We have recently reported on a new probe, the Fiber Deflection Probe (FDP), for diameter and form measurement of large aspect ratio micro-holes (100 um nominal diameter, 5 mm deep). In this paper, we briefly review the measurement principle of the FD ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=823200

28. Fiber Deflection Probe for Small Hole Metrology
Published: 1/1/2006
Authors: Balasubramanian Muralikrishnan, Jack A Stone Jr., John Richard Stoup
Abstract: This paper presents the development of a new probing method for Coordinate Measuring Machines (CMM) to inspect diameter and form of small holes. The technique, referred to as fiber deflection probing, can be used for holes of approximately 100 mm nom ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=822250

29. A Fiber Probe for CMM Measurements of Small Features
Published: 8/1/2005
Authors: Jack A Stone Jr., Balasubramanian Muralikrishnan, John Richard Stoup
Abstract: We report on performance of a new form of fiber probe, which can be used in conjunction with a coordinate measuring machine (CMM) for microfeature measurement.  The probe stylus is a glass fiber with a small ball (?75 ?m diameter) glued to the e ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=823194

30. Methods for Evaluating the Reference Value in Laboratory Intercomparisons of Dimensional Measurements
Published: 8/1/2005
Author: Jack A Stone Jr.
Abstract: A number of methods have been proposed to evaluate the reference value for intercomparisons of laboratory measurements. Methods for establishing the reference value include the arithmetic mean, weighted mean (with weights proportional to the reciproc ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=823192



Search NIST-wide:


(Search abstract and keywords)


Last Name:
First Name:







Special Publications:

Looking for a NIST Special Publication (NIST SP Series)? Place the series number and dash in the report number field (Example: 800-) and begin your search.

  • SP 250-XX: Calibration Services
  • SP 260-XX: Standard Reference Materials
  • SP 300-XX: Precision Measurement and Calibration
  • SP 400-XX: Semiconductor Measurement Technology
  • SP 480-XX: Law Enforcement Technology
  • SP 500-XX: Computer Systems Technology
  • SP 700-XX: Industrial Measurement Series
  • SP 800-XX: Computer Security Series
  • SP 823-XX: Integrated Services Digital Network Series