NIST logo

Publications Portal

You searched on: Author: jon pratt

Displaying records 71 to 80 of 83 records.
Resort by: Date / Title


71. Chatter Control and Stability Analysis of a Cantilever Boring Bar Under Regenerative Cutting Conditions
Published: 1/1/2001
Authors: A H Nayfeh, Jon Robert Pratt
Abstract: A theoretical and experimental investigation into the stability of a slender boring bar under regenerative cutting conditions is presented. The bar has been equipped with actuators and sensors for feedback control of its structural dynamics. It is mo ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=821907

72. Regenerative Stablity Analysis of Highly Interrupted Machining
Published: 1/1/2001
Authors: Matthew A. Davies, Jon Robert Pratt, Brian S. Dutterer, Timothy J Burns
Abstract: We discuss theoretical and experimental work that supports the use of very low radia immersion in the high-speed milling of difficult-to-machine materials, such as titanium alloys. Our theory is based upon modeling the cutting process by a kicked ha ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=821868

73. SI Traceability of Force at the Nanonewton Level
Published: 1/1/2001
Authors: David B Newell, Jon Robert Pratt, John A Kramar, Douglas T Smith, L Feeney, Edwin Ross Williams
Abstract: Although nanonewton force measurements are commonplace in industry, no National Measurement Institute supports a link to the International System of Units (SI) below one newton. The National Institute of Standards and Technology has launched a five-y ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=821766

74. Stability Analysis of Interrupted Cutting With Finite Time in the Cut
Published: 1/1/2001
Authors: P V Bayly, J E Halley, Matthew A. Davies, Jon Robert Pratt
Abstract: The stability of interrupted cutting is examined for the case in which the tool is in contact with the work piece for a small, but finite, fraction of the tooth-passing period. A model of a single degree-of-freedom tool excited by intermittent, rege ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=821864

75. Broadband Ac-dc Difference Calibrations of Current Shunts up to 100 A at NIST
Published: 7/1/2000
Authors: Joseph R. Mr. (Joseph R.) Kinard Jr., Thomas E Lipe, Clifton B. Childers, Owen Brede Laug, Jon Robert Pratt
Abstract: NIST is now offering broadband, ac-dc difference calibrations of current shunts from 3 A to 100 A, and at frequencies up to 30 kHz, as special tests. We present an overview of this new service including the design and construction of the NIST standar ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=24120

76. A Measurement System for Characterizing the Detection Performance of Metal Detectors: Design and Operation
Series: NIST Interagency/Internal Report (NISTIR)
Report Number: 6530
Published: 6/1/2000
Authors: Nicholas G Paulter Jr., Donald R Larson, Jon Robert Pratt
Abstract: A measurement system for evaluating the performance of hand-held (HH) and walk-through (WT) metal detectors is described. These detectors produce time-varying magnetic fields that interact with objects comprised of electrically conductive and/or mag ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=13168

77. The Stability of Low Radial Immersion Milling
Published: 1/1/2000
Authors: Matthew A. Davies, Jon Robert Pratt, Brian S. Dutterer, Timothy J Burns
Abstract: Traditional regenerative stability theory predicts a set of spindle speeds with locally optimum stability at integer fractions of the natural frequency of the most flexible mode of the system.  The assumptions of this theory become invalid for h ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=821851

78. Dynamic Interrogation of a Basic Cutting Process
Published: 7/1/1999
Authors: Matthew A. Davies, Michael Kennedy, Jon Robert Pratt, Christopher J. Evans
Abstract: A dynamic cutting fixture based on the test rig pioneered by Peters et al. has been developed to aid investigations of cutting process dynamics. This active fixture consists of a flexure-based tool holder with a single dominant modal direction, two v ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=821933

79. A Wide Bandwidth Printed Wiring Board Transmission Line Probe
Published: 3/1/1999
Authors: Nicholas G Paulter Jr., Jon Robert Pratt
Abstract: An inexpensive, wide bandwidth, high cycle 50 {omega} probe is described for making electrical contact to printed wiring board planar transmission lines. The electrical transfer function of the probe and its contact repeatability are presented.
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=13673

80. Frequency Domain Modal Estimation Techniques, Experimental Techniques
Published: 1/1/1998
Authors: S Fahey, Jon Robert Pratt
Abstract: In this brief, we discuss the estimation of modal parame-ters using single-degree-of-freedom approximations. Then, we proceed to review two multi-degree-of- freedom techniques for modal parameter estimations-the first based on dynamic matrices and th ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=820115



Search NIST-wide:


(Search abstract and keywords)


Last Name:
First Name:







Special Publications:

Looking for a NIST Special Publication (NIST SP Series)? Place the series number and dash in the report number field (Example: 800-) and begin your search.

  • SP 250-XX: Calibration Services
  • SP 260-XX: Standard Reference Materials
  • SP 300-XX: Precision Measurement and Calibration
  • SP 400-XX: Semiconductor Measurement Technology
  • SP 480-XX: Law Enforcement Technology
  • SP 500-XX: Computer Systems Technology
  • SP 700-XX: Industrial Measurement Series
  • SP 800-XX: Computer Security Series
  • SP 823-XX: Integrated Services Digital Network Series